Page 1 of 5
Collection of big mechanical bits for 300s
Posted: 07 Aug 2011 11:54 am
by filthyjohn
My lockup has too much stuff in it, so I'm looking to get rid of some of the spares I'll likely never need.
Here's a small part of the problem:
It's not all volvo stuff there, but most of it is, and it's only about half the total amount.
Off the top of my head I want rid of:
some 360 gearboxes,
some 360 torque tubes (x3),
360 bellhousings, (x4),
mk3 tail lamps (xinfinity),
factory GLT bumpers in black (rear with tow bar),
340 gear linkages,
360 gear linkages,
360 rear axle,
340 rear axle (x2),
340 fuel tanks (x3),
GLT spoilers (x2),
A big pile of interior bits,
A couple of bonnets,
340 driveshafts,
A whole '82 343DL (will write an ad for that soon),
And my 340 16v when I get round to MOTing it.
Thanks for looking, there's probably a lot of other guff I've forgotten about so shout up if you want anything and I'll have a rake about. There's not much rare stuff but plenty of mechanical necessities. Loads of wheels too, will dig them out and start a seperate thread.
Re: Collection of big mechanical bits for 300s
Posted: 07 Aug 2011 12:07 pm
by mattywatsit
John,
Would you be able to put a passenger side front indicator cluster to one side for me please?
Also how much would you be wanting for it?
The seal has gone on mine and lets in water big time
Will try and pop through to see you at some point soon.
Cheers.
Re: Collection of big mechanical bits for 300s
Posted: 07 Aug 2011 12:13 pm
by filthyjohn
Yeah matt, I'll check the pile and get back to you. How's a tenner sound?
Re: Collection of big mechanical bits for 300s
Posted: 07 Aug 2011 02:06 pm
by volvosneverdie
How much for the Viva/Storage bin?
Re: Collection of big mechanical bits for 300s
Posted: 07 Aug 2011 03:13 pm
by filthyjohn
Gav says £750.
Re: Collection of big mechanical bits for 300s
Posted: 07 Aug 2011 04:43 pm
by mattywatsit
filthyjohn wrote:Yeah matt, I'll check the pile and get back to you. How's a tenner sound?
Tenner sounds alright to me mate, just had a look on eBay and there about a tenner plus postage.
Can't collect for a couple of weeks - that alright?
Cheers.

Re: Collection of big mechanical bits for 300s
Posted: 07 Aug 2011 09:16 pm
by Nimminz
oooh v300 aladin's cave right there!
Will have a think of what i need
EDIT: any LH 2.4 stuff?
Re: Collection of big mechanical bits for 300s
Posted: 07 Aug 2011 11:27 pm
by SteveP
Balls - if this was last week that 82 343...

Re: Collection of big mechanical bits for 300s
Posted: 08 Aug 2011 09:59 am
by MCHUDD
Hi John.
I donn't sapose you would have a 1983 eccon dash clock gauge
in the treasure pile
Cheers Mark.
PS That Viva should not be too hard to shift.
Re: Collection of big mechanical bits for 300s
Posted: 08 Aug 2011 10:22 am
by valman
could you check if you have a rev counter please? and if you do, how much + p&p?
cheers
Re: Collection of big mechanical bits for 300s
Posted: 08 Aug 2011 11:39 am
by jon-ovlov
Hi John, any chance of a 1.7 clutch output shaft? And any later type 1.4/1.7 radiator?
Re: Collection of big mechanical bits for 300s
Posted: 08 Aug 2011 10:06 pm
by filthyjohn
Yoicks!
I've had LOADS of interest so what I'll do is write it all down on a piece of paper then go check the stocks tomorrow. I'll PM everyone individually as soon as I work out what I have and what I don't.
Cheers for the patience guys.
SteveP wrote:Balls - if this was last week that 82 343...

O RLY? It's dead cheap to run, and it'll still be here for a little while yet
MCHUDD wrote:Hi John.
I donn't sapose you would have a 1983 eccon dash clock gauge
in the treasure pile

Hey Mark, sorry mate but I don't have one, that's a bit early for me
Nimminz wrote:oooh v300 aladin's cave right there!
Will have a think of what i need
EDIT: any LH 2.4 stuff?
Sorry, no LH 2.4, got a T5 engine though??
mattywatsit wrote:Can't collect for a couple of weeks - that alright?
Yeah mate just give me a shout as+when.
Re: Collection of big mechanical bits for 300s
Posted: 08 Aug 2011 10:50 pm
by jon-ovlov
No need for the clutch shaft any more. Found one.

Re: Collection of big mechanical bits for 300s
Posted: 11 Aug 2011 12:41 am
by Nosher
Hey, would you have a standard 340 1.4 exhaust (full system from the downpipe back)?
Cheers
Alfie
Re: Collection of big mechanical bits for 300s
Posted: 11 Aug 2011 10:43 am
by jon-ovlov
Possible needage of another prop, depending on the turn around of the custom unit.
Also out of interest, how much is the 343 going to be? . . . .